information - regulation
Electrical regulation of KORAFLEX FV, FV InPool, FI, FW, KORALINE LV and KORAWALL WI (hereinafter referred to as fan-coils)
- Group of fans with a unique disk type synchronous engine with permanent magnets. It is characterized mainly by very low power consumption – the power input of the engine at the full range of speed does not exceed 7.5 watts; the engine also runs very quietly.
- Connecting terminal (F Box)
- Exchanger temperature sensor (switch)
The DC power supply source in accordance with the total power input of the controlled fan-coil units. The offer includes 4 sizes for 12V/60W, 12V/100W, 24V/100W and 24V/480W. The power supply sources are supplied separately for installation in the electrical switchboard on DIN rail.
- R-Box, containing the speed signal galvanic separation module, controlling the fan speed and which also allows the selection and optimization of various degrees of speed. The R-Box is designed for mounting on DIN rail in the switchboard.
- Plastic box for the placement of the DC power supply and the R-Box for installations where the switchboard is too far.
- Siemens thermostats
- Valves, thermoelectric drive 12V DC and 24V DC
Specification of 12V DC:
The performance is controlled by the working media On/Off switching valve, if used, and by switching the On/Off the three-speed blower fan. When using a Siemens thermostat RDG100T the speed is controlled automatically. All three speeds of the fan can be smootly adjusted. The fan speed is given by the size of the voltage control signal CNTRL from the galvanic separation signal module (R-Box).
Fans are normally blocked by a temperature switch (TS1) at a switching temperature of about 35 °C. This function may be disconnected (This accessory is not supplied for KORAWALL WI). For fan coils with dry-cooling effect it is still necessary to use one cooling medium thermal switch (TS2) connected in parallel to the temperature switch which activates at a temperature below 13 °C. The temperature and speed is controlled by Siemens Thermostats RAB11, RDF600/IR or RDG 100T. Contact fields of these thermostats (TS1) are connected to mains voltage, and that is why it is necessary to use the R-Box signals' galvanic separation (the galvanic separation of signals is implemented by using optocouplers).
The thermostat switches the DC power supply source of the output voltage of approx. 12 V. Once the power supply source is switched on the heating medium valves (if used) start opening. Furthermore, the thermostat through galvanic separation module generates the control voltage signal CNTRL. The control voltage signal is of three levels, with each speed level smootly adjustable. The standard regulation enables the use of a themoelectric drive 12 V DC that closes or opens the heating media valve. The function is set in such a way that if heating is required, i.e. after the thermostat switches on, the power supply is activated. The voltage from the power supply source directly supplies the thermoelectric drives of the valve for the control of the heating media inlet to the fan-coil unit.
Specification of 24V DC:
The performance is controlled by switching On/Off the working medium valve - provided such valve is implemented - and by switching On/Off the blowing fan. The convector is under permanent voltage of 24 V. The thermostat Siemens RDG 160T controls via thermo-drive the valve of the heating media as On/Off and furthermore it controls the speed of the fan via voltage signal 0-10 V. The speed of the fan may be controlled automatically or manually in three speed levels. The speed levels may be adjusted. The fans are as standard blocked by temperature switch (TS1) at switching temperature of about 35 °C. This function may be disconnected (This accessory is not supplied for KORAWALL WI). As for fan coils with cooling effect the second thermal switch (TS2) for cooling media is implemented to switch On when the temperature falls below 13°C.
BMS (Building Management System):
The convectors control can be also carried out using a BMS (Bulding Management System) higher-level output elements. One BMS relay output controls the valve's opening/closing, and the second continuous 0–10 V output controls the speed.
Description of regulation of KORAFLEX FV InPool
The above described system of regulation applies to pool applications for which this product is intended. The principle is the same but the electrical equipment of the convector differs the electronics of the motor, F box are located in a plastic box with high degree of protection IP 67 which is placed inside the convector. When installing the connecting cables to the terminal block of the F box must be connected as per instructions. In terms of temperature and speed regulation the same types and variations of thermostats are used with a restriction that the thermostats must not be placed in the pool area. For these purposes we recommend using the temperature sensor which senses the temperature in the pool area, see Accessories. The sensor is designed for thermostats RDF 600 and RDG 100T.
The convector is not designed for continuous flooding by pool water. Get thoroughly familiar with the warranty and operating conditions.
Installation must be performed according to valid standards and safety regulations! The manufacturer is not liable for defects or damage caused by improper installation.
Higher heat outputs and smarter design of KORALINE bench convectors
Local ventilation unit KORASMART TUBE with heat recovery
A new model of vertical panel radiator RADIK PREMIUM which thanks to its design and dimensions enables installation even in atypical spaces